pd-95210 IRF7807VPBF 11/3/04 device characteristics n channel application specific mosfet ideal for mobile dc-dc converters low conduction losses low switching losses 100% r g tested lead-free descriptionthis new device employs advanced hexfet power mosfet technology to achieve an unprecedented balance of on-resistance and gate charge. the reduction of conduction and switching losses makes it ideal for high efficiency dc-dc converters that power the latest generation of mobile microprocessors. a pair of irf7807v devices provides the best cost/ performance solution for system voltages, such as 3.3v and 5v. top view 8 12 3 4 5 6 7 d d d d g s a s s so-8 irf7807v r ds(on) 17 m ? q g 9.5 nc q sw 3.4 nc q oss 12 nc absolute maximum ratings symbol units v ds v gs continuous drain or source t a = 25c (v gs 4.5v) t a = 70c i dm t a = 25c t a = 70c t j , t stg c i s i sm thermal resistance symbol typ max units r ja CCC 50 r jl CCC 20 a w a c/w parameter maximum junction-to-ambient maximum junction-to-lead junction & storage temperature range continuous source current (body diode) pulsed source current parameter v power dissipation drain-source voltage gate-source voltage pulsed drain current p d i d irf7807v 8.32.5 66 2.5 -55 to 150 1.6 66 30 20 6.6 hexfet power mosfet downloaded from: http:///
IRF7807VPBF 2 www.irf.com notes: repetitive rating; pulse width limited by max. junction temperature. pulse width 400 s; duty cycle 2%. when mounted on 1 inch square copper board typ = measured - q oss typical values of r ds (on) measured at v gs = 4.5v, q g , q sw and q oss measured at v gs = 5.0v, i f = 7.0a.
* device are 100% tested to these parameters. electrical characteristics parameter symbol min typ max units drain-source breakdown voltage bv dss 30 CCC CCC v static drain-source on-resistance r ds(on) CCC 17 25 m ? gate threshold voltage v gs(th) 1.0 CCC 3.0 v CCC CCC 100 CCC CCC 20 CCC CCC 100 gate-source leakage current* i gss CCC CCC 100 na total gate charge* q g CCC 9.5 14 pre-vth gate-source charge q gs1 CCC 2.3 CCC post-vth gate-source charge q gs2 CCC 1.0 CCC gate-to-drain charge q gd CCC 2.4 CCC switch charge (q gs2 + q gd )q sw CCC 3.4 5.2 output charge* q oss CCC 12 16.8 v ds = 16v, v gs = 0 gate resistance r g 0.9 CCC 2.8 ? turn-on delay time t d(on) CCC 6.3 CCC rise time t r CCC 1.2 CCC turn-off delay time t d(off) CCC 11 CCC fall time t f CCC 2.2 CCC source-drain ratings and characteristics parameter symbol min typ max units diode forward voltage* v sd CCC CCC 1.2 v reverse recovery charge (with parallel schottsky) 64 CCC i s = 7.0a ,v gs = 0v CCC q rr conditions v gs = 0v, i d = 250a v gs = 4.5v, i d = 7.0a v ds = v gs , i d = 250a v ds = 30v, v gs = 0 v gs = 20v i dss drain-source leakage current v ds = 16v v ds = 24v, v gs = 0 v ds = 24v, v gs = 0, t j = 100c v gs = 5v, i d = 7.0a a nc ns conditions v gs = 5v, r g = 2 ? v dd = 16v i d = 7a resistive load CCC nc reverse recovery charge di/dt = 700a/s , (with 10bq040)v ds = 16v, v gs = 0v, i s = 7.0a di/dt = 700a/s v ds = 16v, v gs = 0v, i s = 7.0a q rr(s) CCC 41 downloaded from: http:///
IRF7807VPBF www.irf.com 3 control fet special attention has been given to the power losses in the switching elements of the circuit - q1 and q2.power losses in the high side switch q1, also called the control fet, are impacted by the r ds(on) of the mosfet, but these conduction losses are only about one half of the total losses. power losses in the control switch q1 are given by;p loss = p conduction + p switching + p drive + p output this can be expanded and approximated by; p loss = i rms 2 r ds(on ) () + i q gd i g v in f ? ? ? ? ? ? + i q gs 2 i g v in f ? ? ? ? ? ? + q g v g f () + q oss 2 v in f ? ? ? ? this simplified loss equation includes the terms q gs2 and q oss which are new to power mosfet data sheets. q gs2 is a sub element of traditional gate-source charge that is included in all mosfet data sheets.the importance of splitting this gate-source charge into two sub elements, q gs1 and q gs2 , can be seen from fig 1. q gs2 indicates the charge that must be supplied by the gate driver between the time that the thresholdvoltage has been reached (t1) and the time the drain current rises to i dmax (t2) at which time the drain volt- age begins to change. minimizing q gs2 is a critical fac- tor in reducing switching losses in q1. q oss is the charge that must be supplied to the out- put capacitance of the mosfet during every switch-ing cycle. figure 2 shows how q oss is formed by the parallel combination of the voltage dependant (non- linear) capacitances c ds and c dg when multiplied by the power supply input buss voltage. figure 1: typical mosfet switching waveform synchronous fet the power loss equation for q2 is approximated by; p loss = p conduction + p drive + p output * p loss = i rms 2 r ds(on) () + q g v g f () + q oss 2 v in f ? ? ? ? ? + q rr v in f ( ) *dissipated primarily in q1. power mosfet selection for dc/dcconverters 4 12 drain current gate voltage drain voltage t3 t2 t1 v gth q gs1 q gs2 q gd t0 downloaded from: http:///
IRF7807VPBF 4 www.irf.com typical mobile pc application the performance of these new devices has been tested in circuit and correlates well with performance predic- tions generated by the system models. an advantage of this new technology platform is that the mosfets it produces are suitable for both control fet and synchro- nous fet applications. this has been demonstrated with the 3.3v and 5v converters. (fig 3 and fig 4). in these applications the same mosfet irf7807v was used for both the control fet (q1) and the synchronous fet (q2). this provides a highly effective cost/performance solution. figure 3 figure 4 figure 2: q oss characteristic for the synchronous mosfet q2, r ds(on) is an im- portant characteristic; however, once again the im- portance of gate charge must not be overlooked since it impacts three critical areas. under light load the mosfet must still be turned on and off by the con- trol ic so the gate drive losses become much more significant. secondly, the output charge q oss and re- verse recovery charge q rr both generate losses that are transfered to q1 and increase the dissipation in that device. thirdly, gate charge will impact the mosfets susceptibility to cdv/dt turn on. the drain of q2 is connected to the switching node of the converter and therefore sees transitions be-tween ground and v in . as q1 turns on and off there is a rate of change of drain voltage dv/dt which is ca-pacitively coupled to the gate of q2 and can induce a voltage spike on the gate that is sufficient to turn the mosfet on, resulting in shoot-through current .the ratio of q gd /q gs1 must be minimized to reduce the potential for cdv/dt turn on. spice model for irf7807v can be downloaded in machine readable format at www.irf.com.
83 84 85 86 87 88 89 90 91 92 93 12345 load current (a) efficiency (%) vin=24v vin=14v vin=10v 86 87 88 89 90 91 92 93 94 95 12345 load current (a) efficiency (%) vin=24v vin=14v vin=10v downloaded from: http:///
IRF7807VPBF www.irf.com 5 fig 5. normalized on-resistance vs. temperature fig 6. typical gate charge vs. gate-to-source voltage fig 7. on-resistance vs. gate voltage fig 8. typical source-drain diode forward voltage -60 -40 -20 0 20 40 60 80 100 120 140 160 0.0 0.5 1.0 1.5 2.0 t , junction temperature ( c) r , drain-to-source on resistance (normalized) j ds(on) v = i = gs d 4.5v 7.0a 0 2 4 6 8 10 12 0 1 2 3 4 5 q , total gate charge (nc) v , gate-to-source voltage (v) g gs i = d 7.0a v = 16v ds 0.1 1 10 100 0.2 0.4 0.6 0.8 1.0 1.2 v ,source-to-drain voltage (v) i , reverse drain current (a) sd sd v = 0 v gs t = 25 c j t = 150 c j 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 v gs, gate -to -source voltage (v) 0.010 0.015 0.020 0.025 0.030 r d s ( o n ) , d r a i n - t o - s o u r c e o n r e s i s t a n c e ( ? ) i d = 7.0a downloaded from: http:///
IRF7807VPBF 6 www.irf.com figure 9. maximum effective transient thermal impedance, junction-to-ambient 0.1 1 10 100 0.00001 0.0001 0.001 0.01 0.1 1 10 notes: 1. duty factor d = t / t 2. peak t = p x z + t 1 2 j dm thja a p t t dm 1 2 t , rectangular pulse duration (sec) thermal response (z ) 1 thja 0.01 0.02 0.05 0.10 0.20 d = 0.50 single pulse (thermal response) downloaded from: http:///
IRF7807VPBF www.irf.com 7 so-8 package outlinedimensions are shown in milimeters (inches) e1 de y b aa1 h k l .189 .1497 0 .013 .050 basic .0532 .0040 .2284 .0099 .016 .1968 .1574 8 .020 .0688 .0098 .2440 .0196 .050 4.80 3.80 0.33 1.35 0.10 5.80 0.25 0.40 0 1.27 b as ic 5.00 4.00 0.51 1.75 0.25 6.20 0.50 1.27 min max millimeters inches min max dim 8 e c .0075 .0098 0.19 0.25 .025 basic 0.635 bas ic 87 5 65 d b e a e 6x h 0.25 [.010] a 6 7 k x 45 8x l 8x c y 0.25 [.010] cab e1 a a1 8x b c 0.10 [.004] 43 12 f oot p r i nt 8x 0.72 [.028] 6.46 [.255] 3x 1.27 [.050] 4. ou t l i ne conf or ms t o j e de c ou t l i ne ms -012aa. not e s : 1. dimens ioning & t olerancing pe r as me y14.5m-1994. 2. cont roll ing dime ns ion: mil lime te r 3. di me ns i ons ar e s h own i n mi l l i me t e r s [i nch e s ] . 5 dimens ion doe s not incl ude mol d prot rus ions . 6 dimens ion doe s not incl ude mol d prot rus ions . mold prot rus ions not t o e xce e d 0.25 [.010]. 7 dimens ion is t he le ngt h of l e ad f or s ol dering t o a s ubs t rat e. mold prot rus ions not t o e xce e d 0.15 [.006]. 8x 1.78 [.070] so-8 part marking information (lead-free) dat e code (yww) xxxx int ernat ional rect ifier logo f 7101 y = l as t digit of t he ye ar part number lot code ww = we e k example: t his is an irf7101 (mosfet ) p = de s i gnat e s l e ad-f r e e product (optional) a = as s e mb l y s i t e code downloaded from: http:///
IRF7807VPBF 8 www.irf.com data and specifications subject to change without notice. this product has been designed and qualified for the consumer market. qualification standards can be found on irs web site. ir world headquarters: 233 kansas st., el segundo, california 90245, usa tel: (310) 252-7105 tac fax: (310) 252-7903 visit us at www.irf.com for sales contact information . 11/04 330.00 (12.992) max. 14.40 ( .566 ) 12.40 ( .488 ) notes : 1. controlling dimension : millimeter. 2. outline conforms to eia-481 & eia-541. feed direction terminal number 1 12.3 ( .484 ) 11.7 ( .461 ) 8.1 ( .318 ) 7.9 ( .312 ) notes: 1. controlling dimension : millimeter. 2. all dimensions are shown in millimeters(inches). 3. outline conforms to eia-481 & eia-541. so-8 tape and reeldimensions are shown in milimeters (inches) downloaded from: http:///
|
